55HP Hydraulic Chain Feed 140mm Wood Chipper
55HP 140mm 3 tons/hour Chain-Feed Diesel Wood Chipper
The 6140 Chain-Feed Diesel Wood Chipper is a tow-behind branch shredder for roadside, orchard and green-waste work. A 1,100 mm chain plate carries limbs to a 330 × 280 mm throat, a Ø280 mm hydraulic roller feeds them into a 300 mm knife drum, and a four-cylinder 40 kW (54.4 hp) diesel drives four fly knives and one bed knife at 2,900 r/min. Rated output is 3 t/h on limbs up to 140 mm.
Feed runs on a three-position lever - forward, reverse, stop - with an intelligent control that reverses the roller when rotor speed drops. The discharge chute turns a full 360° on a quick-adjust mount. Road tyres, tail lights, an infeed work light, a folding hand-crank jack and an adjustable drawbar are fitted, so one person tows the unit between sites and levels it on arrival. Typical sites: garden maintenance, orchard waste, community green areas, small municipal yards.
1,100mm chain plate - limbs are laid flat and carried to the throat; nobody holds material in the air
Reversing Ø280mm roller - a bridged fork is walked back out with the engine running
2,950 × 1,300 × 1,800mm trailer - 165/70 R13 tyres, adjustable drawbar, one-person levelling

Pre-shipment test
Rigorous testing before shipment for dependable operation.
CE documentation
Machinery Directive attestation of conformity per unit.
Reply within 24 h
Technical questions answered within one working day.
Knife & wear parts
Spare parts list issued with the machine.
Two Infeed Options, One Power Unit
Standard Feeding or 1,100 mm chain plate - same 40 kW (54.4 hp) diesel, same 300 mm drum

Standard Feeding
600 × 500 mm opening, 330 × 280 mm throat. Limbs are placed at the throat and held by hand while the roller pulls. Suits crews working short, straight prunings at a fixed yard.

Chain Plate Feeding
1,100 mm chain plate carries limbs to the throat and the Ø280 mm roller takes over. The operator loads flat, at waist height, and steps back. Suits roadside work, crooked orchard limbs and one-operator sites.
Both versions share the 4 + 1 knife set and the 20 L hydraulic circuit; only the infeed differs. State the infeed type on the order.
Main Features
Key Built‑in Advantages for Professional Chipping Work
Knife Drum and Knife Set:
300 mm knife drum, 4 fly knives + 1 bed knife, 155 mm blade length, main shaft at 2,900 r/min.
Hydraulic Feed System:
Ø280 mm roller on a hydraulic motor; 600 × 500 mm opening; 330 × 280 mm throat; 3-position manual control (forward / reverse / stop) plus intelligent control; 20 L tank.
Feed Opening Sized for Forks:
600 × 500 mm opening takes crooked and forked limbs; the 330 × 280 mm throat sets the limit - anything wider is cut before it is fed.
Trailer‑type Mobile Chassis:
2,950 × 1,300 × 1,800 mm; 165/70 R13 tyres on 13-inch alloy rims; tail lights, infeed work light, folding hand-crank jack, adjustable drawbar height.
360° Rotatable Discharge Outlet:
The chute turns a full circle on a quick-adjust mount, so the pile is placed beside the tow vehicle rather than behind it.
Electrics:
600 W generator, 12V 105 Ah battery, electric start. The generator is sized for the infeed work light, not for external tools.
Complete Accessories:
One tool kit supplied with each unit; the knife-change sequence needs no special press.
Where it Works:
Orchard pruning, landscaping, park maintenance and municipal green waste, on limbs up to 140 mm.
Models Display
Four models, 2 t/h to 8 t/h - the 6140 on this page is the 3 t/h / 140 mm unit




Output ratings are factory figures on fresh-cut material within each model's branch limit.
Wood Chipper Details
Key Structural Details & Performance Advantages

3 mm Engine Cover
Bent steel cover over the engine bay, hinged for daily checks.

Roller Lifts for Inspection
The pressure roller lifts clear, so the crushing chamber is inspected without removing the feed table.

Two Hydraulic Motors
One drives the chain plate, one drives the pressure roller; both work from the same 20 L circuit.

120 L Fuel Tank
120-liter capacity, supports up to 20 hours of continuous operation on a full tank.

Reinforced Traction
Ensure that the machine can operate normally in rough and uneven mountain road conditions.

Pluggable Harness
Aviation-type connectors at the panel; the loom unplugs instead of being cut for service.

Hand-crank Jack
Mounted on the frame, lifts the pressure roller for knife access.

Battery Isolator
Cuts the circuit when the machine is parked.
Engine options and colour are set at order; the standard unit uses the 40 kW (54.4 hp) four-cylinder diesel.
Wood Chipper Parameters
Accurate Index For Wood Chipping Machine
| products | ![]() |
![]() |
![]() |
![]() |
| Model number | LC-6130 | LC-6140 | LC-6145 | LC-6175 |
| Power | 32HP | 55HP | 102HP | 197HP |
| Output | 2 ton/hour | 3 ton/hour | 5 ton/hour | 8 ton/hour |
| Size | 2300×1300×1800mm | 2300×1350×1800mm | 3200×1700×2400mm | 5200×2250×3200mm |
| Blade Roller Disc Dia. | 300mm | 330mm | 500mm | 750mm |
| Engine Speed | 2600r/min | 2900r/min | 2500r/min | 1600r/min |
| Blade Quantity | 4 Moving,1 Static | 4 Moving,1 Static | 4 Moving,1 Static | 8 Moving,1 Static |
| Blade Length | 155mm | 155mm | 230mm | 215mm |
| Feed Roller Dia. | 280mm | 280mm | 500mm | 600mm |
| Max Shredding Dia. | ≤130mm | ≤140mm | ≤250mm | ≤300mm |
| Hydraulic Tank Cap. | 20L | 20L | 25L | 50L |
| Generator Power | 600w | 600w | 800w | 800w |
| Battery Specs | 12V 105aH | 24V 85aH | 24V 105aH | 24V 105aH |

Control Panel With Nine Readouts and Switches
Readouts are shown in °C, V and r/min; the hour meter sets the service interval.
① Throttle up and down buttons
② One-click start & stop, electric shutdown
③ One-click switching for intelligent feeding
④ Engine speed
⑤ Oil pressure monitoring
⑥ Water temperature & oil temperature monitoring
⑦ Battery voltage display
⑧ Working hour record
⑨ Main engine speed
Four-fold Safety Protection
Four stop paths between the operator and the feed roller




Press to stop, twist to reset; the circuit stays open until the button is released.
Cuts the feed circuit at the panel.
Bar at the infeed; pushing it stops the feed roller.
The feed stops on light contact, before the operator reaches the drum.
Wood Chipper Applications
The 140mm 3 tons/hour Wood Chipper Prunings, orchard limbs, bamboo, palm frond bases and twig bundles, from 20 mm to 140 mm. Chips leave through the 360° chute and are stockpiled, used as mulch, or composted. Anything above 140 mm is cut before it reaches the feed table - the throat is 330 × 280 mm.





Shredding Effect
Chip size depends on knife setting and wood species.






Packing & Shipping
Units ship palletised or in a 20 ft / 40 ft container depending on model. The 6140 measures 2,950 × 1,300 × 1,800 mm; the discharge chute is turned to the transport position and the drawbar height is set before loading. Sea, rail and road forwarding. Loading photos and the packing list are sent before departure.




Certifications
Machinery Directive attestation of conformity for the wood chipper line. ISO 9001 covers the production system. Certificate copies are sent with the quotation on request.

Wood Chipper CE · 6130

Wood Chipper CE · 6140

Wood Chipper CE · 6145

Wood Chipper CE · 6175

Lawn Mower CE

Ditching Machine CE
Our Service
01
Pre-sale service
Send the branch diameter you chip, the site (roadside, orchard, yard) and the country. The reply is a model recommendation with the matching infeed type, the towing requirements for that market, and a quotation for the 6140 Chain-Feed Diesel Wood Chipper.
02
Production & Shipment
Production photos and a pre-shipment test video; third-party inspection supported; delivery date confirmed at order.
03
After-sales service
12-month warranty on core components; 24-hour online support; remote diagnosis; spare knife sets and wear parts shipped against the parts list.


Shandong Xinleichuang Machinery Co., Ltd
We are always at your service when you need!
Our company is located in Jining, Shandong Province. We are a group enterprise integrating R&D, manufacturing and trading services.
We have multiple coordinated departments: Technical Center, Domestic Trade Department, International Trade Department, Production Department, Quality Inspection Department, Logistics Department and After-sales Service Department.
With years of continuous efforts and innovation, we have developed into a professional machinery manufacturer specializing in large-scale, complete-set, technical and energy-efficient equipment.
Factory Area
years experience
Export Countries
Employee



Welcome customer visits




FAQ
Q: Are you manufacturer or trade company?
A: We are manufacturer, we have our own factory. Our factory has department for exploitation , producing, sales, after-sell service, packing , warehouse, we can offer you best products and best service.
Q: Are you interested in dealership with local company?
A: Yes, we are quite interested in this business cooperation. We'd like to cooperate with some local partner to sell more machines in local market and supply better service. We can discuss more if you also interested.
Q: Do you sell accessories for your machine?
A: Yes, all of matching accessories for our machine are on selling, we are willing to supply the matching parts to you with low price.
Q: What's your terms of payment?
A: Generally,30% as front money, and 70% before delivery. We'll show you the photos of the products and test videos.
Q: What's your terms of delivery?
A: EXW, FOB, CIF, DDU, DDP.
Q: How do you make our business long-term and good relationship?
A: 1. We keep good quality and competitive price to ensure our customers benefit;
2. We respect every customer as our friend, no matter where they come from;
3. If you have any feedback that is cherished to us, please send email to us.
Q: Do you provide OEM/ODM Service?
A: Yes, offer me necessary information, we provide custom-make service to meet different needs of global clients with different budgets.
Q: Do you have CE certificate ?
A: Yes, we have the CE certificate.
Hot Tags: 140mm chain-feed diesel wood chipper, China 140mm chain-feed diesel wood chipper manufacturers, factory
| Model | 6130 | 6140 | 6145 | 6175 |
| Power | 32HP | 55HP | 102HP | 197HP |
| Output | 2 ton/hour | 3 ton/hour | 5 ton/hour | 8 ton/hour |
| Size | 2300×1300×1800mm | 2300×1350×1800mm | 3200×1700×2400mm | 5200×2250×3200mm |
| Blade Roller Disc Dia. | 300mm | 330mm | 500mm | 750mm |
| Engine Speed | 2600r/min | 2900r/min | 2500r/min | 1600r/min |
| Blade Quantity | 4 Moving,1 Static | 4 Moving,1 Static | 4 Moving,1 Static | 8 Moving,1 Static |
| Blade Length | 155mm | 155mm | 230mm | 215mm |
| Feed Roller Dia. | 280mm | 280mm | 500mm | 600mm |
| Max Shredding Dia. | ≤130mm | ≤140mm | ≤250mm | ≤300mm |
| Hydraulic Tank Cap. | 20L | 20L | 25L | 50L |
| Generator Power | 600w | 600w | 800w | 800w |
| Battery Specs | 12V 105aH | 24V 85aH | 24V 105aH | 24V 105aH |
140mm 3 tons/hour Wood Chipper




