18HP Diesel Walk-Behind Tracked Chain Trencher
Where This Trencher Fits
Most trench work on a built site runs into access before it runs into digging. The line sits tight against a boundary wall, or drops between two planting beds, or crosses a lawn that has to stay intact, or passes through a gate no wider machine will clear. A ride-on trencher will not fit, and a mini-excavator costs more in surface repair than the trench is worth.
That limit is the reason the machine is this size. This is a walk-behind chain trencher: one operator walks it, the chain cuts the trench, and it reaches the ground the larger plant cannot. The work is ordinary: irrigation and water lines, power and communications conduit, land drainage, fence lines and garden edging. Every one of those is a job that otherwise comes off a spade and a bar.
Ground it cuts, ground it does not. Soil, gravel, sand and compacted ground are all workable. Bedrock, reinforced concrete and demolition rubble are not, and no chain setting changes that. Those jobs need a rock wheel or a breaker.
① 12–40 cm Trench, Six Chain Widths
Chain width sets the trench, and maximum depth is matched to the chain fitted. A 12 cm chain digs to 100 cm; a 40 cm chain digs to 40 cm. One machine therefore covers pipe, conduit and drainage work that would otherwise need two or three single-purpose units.
② Electric-Hydraulic Lift, 360° Handle
Depth is set from a switch on the handle, so there is no manual jack to wind and no second person holding the boom. The handle turns a full circle, which lets the operator stand on the side where the chain and the marked line are both visible, even tight against a wall.
③ Wheeled Or Tracked, Same Boom
The same machine is built on lugged drive wheels with a front caster, or on two rubber tracks for wet grass, loose soil, sand and side slopes. Only the running gear changes.

Wheeled vs Tracked Trencher
same 18 HP air-cooled diesel, same 12–40 cm trench, 10–100 cm depth at 150–200 m/h

Wheeled Trencher
Lighter, and it moves itself. Two lugged drive wheels and a front caster carry the machine, so it rolls between trenches and up onto a trailer without ramps or lifting gear.
Finished paving stays intact. Lugged tyres cross concrete, asphalt and block paving without the scuffing and marking a track frame leaves behind.
Less to service, less to replace. No track frames, no track tension to set, no track to clean out after mud; running-gear upkeep is the wheel bearings and the caster.
Best for dry, firm, level ground: orchard rows, roadside verges and green belts, courtyards, and trenching along road edges.

Tracked Trencher
Low ground pressure. Two rubber tracks spread the machine's weight along the full contact length, so it sits on soft ground instead of sinking into it.
Traction that holds. The tracks keep grip on wet grass, loose sand and side slopes where a driven tyre spins.
Less compaction where it counts. The same weight is carried over the whole contact length rather than two tyre patches, so lawn, topsoil and seedbed are pressed less.
Best for wet or muddy farmland, waterlogged ground, terraced fields, slopes, loose sand and unmade off-road sites.
Both undercarriages carry the same boom assembly: an 18 HP air-cooled diesel engine, six chain widths from 12 to 40 cm, and a digging depth of up to 100 cm. Electric-hydraulic lift gives working rates of 150–200 m/h (490–660 ft/h), and the handle rotates a full 360°. Only the running gear differs. State the undercarriage and the chain width on the order.
Choose by the ground, not by the trench. Firm, level, finished surfaces take wheels; soft, wet, sloping or unmade ground takes tracks. Trench width and depth are identical on both.
Trencher Details
Key Structural Details & Performance Advantages

Powerful Engine
Powerful 18 HP branded diesel engine delivers stable performance, low fuel consumption, long service life and superior trenching results.

Alloy Blades
High-strength manganese steel trenching chain with alloy tips, wear-resistant and durable, adaptable to various soil conditions.

Adjustable Trenching Size
Trenching depth and width can be adjusted by replacing the chain and attachments to satisfy different construction requirements.

360° Rotation Handle
Humanized handheld design with 360° rotation, simple operation and easy control, supporting side operation.

Spiral Soil Remover
The spiral soil remover efficiently discharges excavated soil, avoids backfilling and guarantees high construction efficiency.

Wider Tires
Wider tires boost traction and evenly distribute machine weight to avoid sinking on soft ground. Crawler tracks are optional.
Chain Trencher Parameters
Accurate Index For Road Base Spreading
| products | ![]() |
![]() |
|||||
| chain | Single chain | Double chain | |||||
| Working Width | 12 cm (4.7 in) | 15 cm (5.9 in) | 20 cm (7.9 in) | 25 cm (9.8 in) | 30 cm (11.8 in) | 40 cm (15.7 in) | |
| Max Trenching Depth | 100 / 110 cm (39 / 43 in) | 90 / 100 cm (35 / 39 in) | 80 / 90 cm (31 / 35 in) | 60 / 70 cm (24 / 28 in) | 50 / 60 cm (20 / 24 in) | 40 / 50 cm (16 / 20 in) | |
| Engine Type | Diesel | Lifting Mode | Electric-hydraulic |
| Engine Brand | ETK | Clutch Mode | Belt tightening type |
| Output Power | 18HP | Weight | 280kg+ |
| Trench Width | 12-40cm | Machine Size | 270*100*120cm |
| Trench Depth | 10-100cm | Handle | 360°Rotatable Control |
Chain Trencher Applications

Orchard fertilization trenching
Farmland irrigation and drainage ditching
Furrowing for cash crop cultivation
Drip & sprinkler pipeline laying
Power & communication cable trenching
Water, sewage & gas pipe installation
Roadside drainage ditching
Frozen & hard soil operation
Landscaping & lawn projects
Small-scale construction sites




Tell us your trench size and soil condition for the right chain and engine configuration.
Packing & Shipping
Units ship in a reinforced steel frame or wooden case, depending on model. The standard 18HP walk-behind chain trencher measures approx. 2700×100×1200 mm; the handlebar is folded down and the digging chain is firmly secured before loading. Sea, rail and road forwarding through our cooperative forwarders. Loading photos and the packing list are sent before departure.




Certifications
Machinery Directive attestation of conformity for the wood chipper line. ISO 9001 covers the production system. Certificate copies are sent with the quotation on request.

Ditching Machine CE

Wood Chipper CE

Spreader CE

Tractor CE

Lawn Mower CE

Grader CE
Our Service
01
Pre-sale service
Please tell us your required trenching depth & width, working site and destination country. We will reply with model recommendation, matched chain configuration and quotation.
02
Production & Shipment
Production photos and a pre-shipment test video; third-party inspection supported; delivery date confirmed at order.
03
After-sales service
12-month warranty on core components; 24-hour online support; remote diagnosis; spare knife sets and wear parts shipped against the parts list.


Shandong Xinleichuang Machinery Co., Ltd
We are always at your service when you need!
Our company is located in Jining, Shandong Province. We are a group enterprise integrating R&D, manufacturing and trading services.
We have multiple coordinated departments: Technical Center, Domestic Trade Department, International Trade Department, Production Department, Quality Inspection Department, Logistics Department and After-sales Service Department.
With years of continuous efforts and innovation, we have developed into a professional machinery manufacturer specializing in large-scale, complete-set, technical and energy-efficient equipment.
Factory Area
years experience
Export Countries
Employee



Welcome customer visits




FAQ
Q: Are you manufacturer or trade company?
A: We are manufacturer, we have our own factory. Our factory has department for exploitation , producing, sales, after-sell service, packing , warehouse, we can offer you best products and best service.
Q: Are you interested in dealership with local company?
A: Yes, we are quite interested in this business cooperation. We'd like to cooperate with some local partner to sell more machines in local market and supply better service. We can discuss more if you also interested.
Q: Do you sell accessories for your machine?
A: Yes, all of matching accessories for our machine are on selling, we are willing to supply the matching parts to you with low price.
Q: What's your terms of payment?
A: Generally,30% as front money, and 70% before delivery. We'll show you the photos of the products and test videos.
Q: What's your terms of delivery?
A: EXW, FOB, CIF, DDU, DDP.
Q: How do you make our business long-term and good relationship?
A: 1. We keep good quality and competitive price to ensure our customers benefit;
2. We respect every customer as our friend, no matter where they come from;
3. If you have any feedback that is cherished to us, please send email to us.
Q: Do you provide OEM/ODM Service?
A: Yes, offer me necessary information, we provide custom-make service to meet different needs of global clients with different budgets.
Q: Do you have CE certificate ?
A: Yes, we have the CE certificate.
Hot Tags: 18hp diesel tracked mini trencher, China 18hp diesel tracked mini trencher manufacturers, factory, Cable Trencher, tracked courier delivery agent, tracked courier delivery provider, tracked freight delivery option, tracked transport delivery agent, Yam Slotting Machine
| Chain | Working Width | Max Trenching Depth |
| Single Chain | 120mm | 1000mm |
| 150mm | 900mm | |
| 200mm | 800mm | |
| Double Chain | 250mm | 650mm |
| 300mm | 500mm | |
| 400mm | 500mm | |
| 400mm | 400mm |
| Engine Type | Diesel | Lifting Mode | Electric-hydraulic |
| Engine Brand | ETK | Clutch Mode | Belt tightening type |
| Output Power | 18HP | Weight | 280kg+ |
| Trench Width | 12-40cm | Machine Size | 270*100*120cm |
| Trench Depth | 10-100cm | Handle | 360°Rotatable Control |


